Chief cook and bottle washer.

Resharpenable Wood Saws

I have found another aspect of traditional woodworking to become slightly obsessive about: re-sharpenable hand saws. Up until a few decades ago, wood saws were made of spring steel and were nearly all intended to be re-sharpened many times over. A carpenter would buy a range of expensive high-quality saws as an apprentice/journeyman, learn how to maintain them, and use them throughout his career. Nowadays, with the possible exception of chainsaw chains and large expensive sawing machine blades, most people use cheap mass-produced hard-point saws that are intended to be thrown away when blunt. Hand saw sharpening has come to be regarded as something of a ‘lost art’.

Don’t get me wrong, the better brands of hardpoint saw intended for professional use aren’t bad – they are very sharp when new and last quite a while as long as you don’t try to cut anything especially abrasive. For the past few months my everyday general purpose hand saw has been a Bahco hardpoint that I pulled out of a skip – a kitchen fitter had chucked it away because it became a little dull after cutting some plastic-coated chipboard worktops.

I believe there are several advantages of re-sharpenable saws:

  1. The good vintage ones are just nicer to look at and use. Well balanced, comfortable, finely shaped hardwood handles. They were expensive items that were meant to last a lifetime.
  2. It’s possible to alter several aspects of tooth shape and set to suit different types of wood.
  3. It’s cheaper in the long run. OK they are more expensive to begin with and you have to occasionally spend a few quid on a new sharpening file, but over the years the cost of all those disposable saws is going to add up.
  4. Related to the previous point, you never need to make that awkward choice that I have faced many times in the past between driving into town and spending £15-£20 on a new saw or continuing to make do with the dull one you’ve already got. Just get out the triangular file and spend ten minutes touching up the teeth.
  5. How environmentally wasteful is it to keep throwing away complete saws just because the edges of the teeth have become slightly rounded?

The main disadvantages are that you have to learn a new skill (not that difficult, it turns out), and because the steel is softer you have to sharpen them more often than you would need to replace a disposable saw.

Got to get to work now, but later on I’ll write a post about my first experience with re-sharpening a hand saw.

Turning Acetal

Tonight I had my first experience of turning acetal (often known by the trademarked name Delrin). It’s an engineering thermoplastic that is relatively expensive but is designed to machine well. I’ve turned other kinds of plastic in the past and usually struggled to get a good accurate smooth finish – they are usually soft and gummy and don’t cut cleanly. Acetal in comparison was a joy to use. With a sharp HSS tool and a high spindle speed, it cuts almost like it’s not there and leaves a lovely smooth finish straight off the tool. You can even take really fine cuts without it rubbing and melting. Lovely!


The part I was making was the sleeve for the bottom part of the bell push button. It will act as an electrical insulator to isolate the switch contacts from the metal part of the button. It also needs to slide smoothly into a hole bored in the wooden backing box underneath the contacts.

Because I have read that most types of glue don’t stick well to acetal, I designed the interface between the two parts of the component in a slightly unusual way. The stainless steel pin was slightly flared towards the end (actually caused by deflection from cutting forces when I turned it, but I expected this to happen and deliberately didn’t do anything to prevent or correct it). Also, the hole in the acetal was drilled 0.5mm larger than the diameter of the pin for roughly the bottom 90% of its length. The combination of the two produced a small tapered gap between the two which, when filled with epoxy resin, should act as a mechanical fixing that will prevent them separating even if the glue doesn’t bond to the plastic at all.


The finished two-part button:


Bellpush Button

Some photos of turning the button for the concertina bellpush this evening. The externally visible dimensions are copied from the metal buttons of my Lachenal English. Underneath the top it’s totally different because it won’t have a conventional lever action (so no need for a cross hole, but it does need a larger diameter lip to stop it coming too far out of the hole in the top). I turned it from 10mm stainless steel rod using a brazed TCT tool bit on my manual Taig lathe.







Impressed with Tracy Tools

Following my previous post, I ordered a set of M2.5 carbon steel taps and a new tap holder from Tracy Tools. They phoned this afternoon to let me know that one of the taps was out of stock but would it be OK if they substituted a (much more expensive) HSS spiral point equivalent at no extra cost? Also, it looked like the tap holder I’d asked for was probably a bit too big for the taps I’d ordered so they would throw in a smaller one too. 😀